Search the Web   


 
HOME >> FAQ
 
Welcome to ask some questions, we will give you some write answers.
 
 

MS Group Hazem Al-Haj Mahmoud Proposal & Quality Assurance Engineer Environmental & Water Sciences Division Munir Sukhtian Group Group Trading Co. Ltd P.O. Box 1027 Amman 11118 鈥?Jordan Tel: +962 6 5650300 鈥?Ext. 139 Fax: +962 6 5650305 Mobile: +962 79 5789020 www.sukhtian.com
　　

Dear Sir I hope this mail finds you well; If you are interested, we have a UF Project with the following specification, Please reply to me if you ar I1. The project is about building a water treatment plant using UF membranes 2. The source of water is a three wells (Mixed of three wells) 3. Total Capacity of the feed water is 110m3/hr 4. The plant will be divided into two identical plants (each with capacity of 55m3/hr). 5. The plant must be able to treat a raw water having following characteristics: § Fluctuated turbidity that could be reached to 20 NTU § E-Coli that could be reached to 20,000 cell/100ml § Other constituents as table below 6. The treated water must have results as below: § Turbidity not more than 1 NTU § E-Coli less than 1.8 cell/100 ml (Most Probable Number), Without Chlorination § Other constituents follows international standards for drinkable water 7. Any Pre-Treatment needed must be recommended by membrane manufacturers 8. UF membranes and system specifications are as below: § Capillary type membranes § Filtration: outside to inside § Filtration mode: Dead end and cross flow § Backwash: a) With product water b) Inside to outside c) Enhanced with air scour outside d) Backwash should be automatic § Flux as recommended by the manufacturer § Membrane material: PVDF (Polyvinylidene Fluoride) § Pressurized system and skid mounted § Modules installed vertically § Recovery: not less than 90% @ 20 NTU Recovery = (Net permeate in 24 hours/Raw water fed in 24 hours) * 100% (NOTE: Net permeate flow = Gross permeate flow - Volume of filtrate required for backwash operation) § Pretreatment should include stainless steel strainer (100-150 Um), or what the manufacturer recommends § System design should include CIP unit with all needed piping, fittings, chemical tank and 316 SS pump and heater & thermostat for heat control § System design should include Integrity Test and Bubble Test units with all needed pipes, fittings and instruments § System design should include automatic CEB system (if it is advised by membrane supplier) § UF modules should be ANSI/NSF standard 61 certified § The designer must fill the attached tables as regard the two cases a) Turbidity of 20 NTU b) Turbidity of less than 5 NTU 9. Average Ions concentration are attached For Any further information, please do not hesitate to contact me Looking forward to receiving your reply before 26 October 2008 With regards and thanks MS Group Hazem Al-Haj Mahmoud Proposal & Quality Assurance Engineer Environmental & Water Sciences Division Munir Sukhtian Group Group Trading Co. Ltd P.O. Box 1027 Amman 11118 – Jordan Tel: +962 6 5650300 – Ext. 139 Fax: +962 6 5650305 Mobile: +962 79 5789020 Website: www.sukhtian.com
　　

Do you carry hollow fiber membrane module with hydrophobic membrane, pore size can be from .1 to 1 micrometer.
　　

FILTER
　　

We are a EPC supplier of water and waste water treatment plants from india. We are interested to use your mbr in our sewage treatment plants. Kindly send catologues and prices and also we can represent you in India. Regards J.R.Moses CEO, HECS(P)L 18,92nd Street, Chennai 600083 Indai 91.09884390811( Mob.) 91.44.43054092 ( Tel.) 91 44. 43054096 ( fax)
　　

    10条记录　每页10条，共2页
 
NORD (HK) ENVIRONMENTAL TECHNOLOGY CO., LTD. All Rights Reserved 2007-2008
Postcode: 300171    Postal Address: NO.85, Qi Wei Road, Hedong District,Tianjin,China.
Phone: 0086-22-89880998  26373728     Facsimile: 0086-22-24382730     Email: nordcompany@yahoo.com nordwater@yahoo.cn    备案正在申请中...